Trigger/ Shutter Release Remote Control for Canon
RF-603 wireless flash trigger consist of two similar transceivers, namely
two or more transceivers can be used at the same time to control camera or
flash lights in order to meet your requirements in creation.
Preparation Before Using:
Slide to open the battery cover in the direction of the arrow, and use the dip
switch to set two transceivers as the same channel, otherwise,it is unable to
control. In order to avoid interfering each other, please set different
transceiver into different channel.
Open the battery room, install two AAA batteries for each transceiver according
to the "+/-" marks shown. Follow the arrow and slide the cover
oppositely to close the battery room.
Slide the power switch to ON, and the power indicator will light(green),slide
the power switch to OFF to turn off.
How to Fix and Install:
1.Fix on light stand
Transceiver can be fixed on the rack with fixing clip such as light stand
bracket(B Type) by hot shoe mounting foot. Switch the flash power off, and
install the flash on the hot shoe of the transceiver, lock the flash and ensure
all are fixed well.
2.Fix on camera
The transceiver can also be fixed on the hot shoe of the camera by hot shoe
mounting foot.RF-603C for
Canon camera,RF-603N for Nikon camera.
One camera controls one or more flashes and studio flash lights.Purchase
different YONGNOU studio flash light control PC cable according to different
studio flash light.
a. Wireless studio flash light trigger sync
1).Insert the PC cable plug with nut into the PC socket of transceiver, and
screw down the nut.
2).Fix the transceiver near the studio flash lights, and insert the cable plug
with jack into the control socket of studio flash lights.
3).Install the transceiver on the hot shoe of the camera, press the release
shutter button of the camera, the studio flash lights and the camera will flash
b.Wireless several flash lights trigger sync
1).Install the flashes on the hot shoe of the transceiver directly,or connected
the studio flash lights with PC cables.
2).Install the transceiver on the hot shoe of the camera, all the flash lights
will by triggering synchronously when shooting.
c.Shutter release remote control
The product may achieve remote shutter release/wireless remote shutter release,
in support of single frame, continuous photograph, delay and bulb shutting modes.
And the modes shall be set on the camera before using. Meanwhile, additional
YOUNGNOU 2.5mm shutter
connecting cable needs to be purchased, which will vary with cameras, current
connecting cables are almost available for all main DSLR.
1).Single transceiver can be used as a remote shutter-release,place a
transceiver on your hand or fix near the camera,and use special shutter cable
between the shutter socket of camera to the transceiver.
2).When it is used as wireless remote shutter release,fix one transceiver on
the hot shoe or near the camera,use special shutter cable between the shutter
socket of camera to the transceiver,and hold the other transceiver.
3).Switch on the camera and the transceiver,press the button halfway of the
transceiver which on you hand,and the camera will focus,press the button
completely to shoot,meanwhile,the red button indicator will work.
If the camera fails to focus,it may take no photograph even signal
recived,adjust the focus mode to "M"(manual)for the lens.
d.Creative flashing: handhold the flash for remote shooting with flash
Take the RF-603 on the flash light as shutter release remote control with flash
trigger synchronously,which is suitable for photographers to adjust
distribution of light,additional YOUNGNOU 2.5mm shutter cables shall be purchased for the
1).Install the handhold flash on the hot shoe of the transceiver as
2).Fix one to the camera on a tripod,install the other transceiver on the hot
shoe of the camera as receiver,and connected with specially shutter cable to
the external shutter socket of the camera.
3).Aim at the object by flash,press the shutter release button of the
transceiver on the flash for remote shooting,and the flash will be triggering
synchronously. Change the angle of the object by handhold flash to trigger for
different lighting effects shooting.
The function is available for single frame shooting mode only.
If the camera fails to focus,it may take no photograph even signal received, adjust
the focus mode to "M"(manual )for the lens.
e. Remote shooting with flash trigger sync
Several RF-603 combination using, purchase additional YOUNGNOU 2.5m shutter cables and the single RF-603
transceiver at least.
1).Install the transceiver on the hot shoe of the camera, which will be
connected with the external socket of the shutter with the shutter cables.
2).Install the flash on the hot shoe of the transceiver, or connected with PC
cable to studio flash lights.
3).Handhold the third transceiver as a remote control transmitter, press the
shutter release button halfway of the transceiver to focus, press the shutter
release button completely to remote shooting with flash trigger sync.
When it is used for combination of RF-603 control of cameras and
flash lights, as the cameras have different reaction time, the shooting time
may be small different.
Type: FSK 2.4GHz wireless remote control system
Shutter Release: half-press, full-press
Shutter Interface:2.5mm socket
Studio Flash Light Interface: standard PC socket
Stand-by Time: over 45hours
1x transmitter+1x receiver+1x shutter connecting cable+1x manual